How to Make a Weed DabberGet Landscape and Gardening Info on mps-landscaping-gardening.com. How to Make a Weed Dabber topic will increase your understanding on Landscape and Gardening Info. We at mps-landscaping-gardening.com only provide news, articles, information in Landscape and Gardening Info. Landscape and Gardening Info at mps-landscaping-gardening.com provides the most up to date news and articles. If you have questions please do not hesitate to contact us.
You are welcome to use this article on your website or in your newsletter as long as you reprint it as is, including the contact information at the end. Website URLs must be active links. You are welcome to use this article with an affiliate link, http://www.freeplants.com/resellers.htm The tool that I am going to tell you about is for using herbicides such as RoundUp. The biggest mistakes that people make when using non-selective herbicides like RoundUp is overspray getting the herbicide on plants that they did not intend to spray, and over applying the product. If you spray to the point of run off, you are applying way too much. The weed dabber is a tool used for spot treating weeds without getting the herbicide on other plants. Start by going to your hardware store and buying a piece of 1- 1/2” PVC pipe. You only need a piece 30” long, but they might make you buy a 10' section. It's pretty cheap though. You'll need a plastic PVC cap for one end of the pipe, and on the other end you'll need an adapter to convert the PVC pipe to a standard pipe thread. You'll have to let the clerk at the hardware store help you find the best combination of fittings to use. What you need to do is to get the PVC pipe reduced down to a male garden hose type fitting. Hardware stores sell brass fittings that convert standard pipe thread to the same thread used on garden hoses. Probably what you'll end up with is an adapter that will convert the 1-1/2” PVC to 3/4” male pipe. Then an adapter to convert the 3/4” male pipe to a male garden house fitting. They also make a cap that you can install on the end of a garden hose, you'll need one of those. This cap must have a rubber garden hose washer in it so it seals properly. The PVC fittings have to be glued on so you'll have to pick up some PVC pipe glue and cleaner. You have to use the cleaner to remove the film and gloss from the PVC pipe and fittings before you glue them. Once you have them cleaned, just apply a coating of glue to both the pipe and the fitting, slide the fitting on and twist it at the same time. Hold the fitting tight for 60 seconds and it will be glued tightly. Cut a piece of pipe 30” long and glue the pipe cap on one end, and the PVC to pipe thread adapter on the other end. Apply a small amount of pipe dope or Teflon tape to the threads of the adapter, and screw the male garden house fitting onto the adapter. Screw the garden hose cap to the male garden hose fitting. Now back to the end of the pipe that you glued the pipe cap to. Drill a very small hole right in the middle of the pipe cap. You might have to experiment a little with the size of the hole you need, but make sure you start with a very small hole. I'd start with 1/16”. Cut a piece of regular household sponge in a square about 1-1/2” square. What you are going to do is place this sponge over the small hole you drilled in the pipe cap, and secure it there by covering it with a piece of lightweight screen or mesh cloth. Maybe even a piece of an onion bag. You can secure the mesh to the PVC pipe with a hose clamp, or electrical tape. Remove the garden hose cap from the other end of the PVC pipe, and fill the pipe with pre-mixed (ready to use) RoundUp. Replace the garden hose cap and you have yourself a weed dabber. The RoundUp will seep out the hole in the end of the pipe cap and be absorbed by the sponge. As long as the garden hose cap is tight, the vacuum in the pipe will keep the herbicide from running out too fast. Once the sponge is damp, you can start dabbing weeds. Remember, you only want the weeds damp and not dripping wet. As long as you are leaving some RoundUp on the weeds as you dab them, the herbicide should kill them. Depending on the temperatures, it could take a week or so before you can see the effects of the herbicide. If the sponge gets too dry you can loosen the cap a little to release the vacuum and more herbicide will be released onto the sponge. Or you can simply turn the tool upside down and that should let some air into the chamber, thus releasing the vacuum. As always, read the label and follow the directions on the herbicide package. Article Index: | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20 | 21 | 22 | 23 | 24 | 25 | 26 | 27 | 28 | 29 | 30 | 31 | 32 | 33 |
More Articles:1. 2 Ways to Safely Transplant Rose Bushes of Any Age By Jon Weaver You will occasionally want to move a rose bush from one location to another, but fear shocking the bush too much and having it die. However, here are two effective ways to minimize the shock to the bush so you can successfully move it to another, more suitable place in your flower garden.The first, and simpler way, is by driving a spade down vertically to its full length of blade about twelve or fifteen inches from the bush and repeating the process in a circular form until all lateral roots … 2. A Kids Tree By Jason Canon During my youth kids were required to pass through a tree climbing phase as part of the transition from being a kid to becoming a teenager. Not just any old tree would do of course. The majestic oak was always a tower of strength but the limbs were too high up for it to be a good climbing tree. Likewise, the tall pecan trees that grew in our yard would have required a chain of ladders just to make it to the first limb.Back toward the center of our property grew a very beautiful Sweet Bay Ma… 3. Tractors and Their History By Johnathan Sanders I recently bought a small tractor for my garden, which prompted me to right this article.The tractor was a John Deere, GT235. John Deere tractors are quite popular in the USA, so thought I would share a few words about the man himself!John Deere was born in Rutland, Vermont in 1804. In 1837 he built the first steel plough, using steel from an old sawmill blade. By 1842 100's of plows and by 1852, Deere & Co. were located in Moline, Illinois, who were producing 4000 ploughs per year. John Deere… 4. Making Memories with Flower Gardening By Sandra Wilson Flower gardening is not only about the present, but can be about the past as well. Although this article is ostensibly about flower gardens, it is really more about carrying memories forward. This will enrich your flower garden.Just three weeks ago, at the time I write this article, my mother- and father-in-law died as a result of a car accident. In the fallout around that, the children, including my husband, had to go through their belongings. We had to sort 90+ years of memories and foun… |
||||
